wdiff draft-ietf-mboned-ssmping-00.txt draft-ietf-mboned-ssmping-01.txt

Network Working Group S. Venaas
Internet-Draft UNINETT
Intended status: Informational May 22, 2007 H. Santos
Expires: November 23, January 10, 2008 July 9, 2007

ssmping Protocol
draft-ietf-mboned-ssmping-00
draft-ietf-mboned-ssmping-01

Status of this Memo

By submitting this Internet-Draft, each author represents that any
applicable patent or other IPR claims of which he or she is aware
have been or will be disclosed, and any of which he or she becomes
aware will be disclosed, in accordance with Section 6 of BCP 79.

Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.

Internet-Drafts are draft documents valid for a maximum of six months
and may be updated, replaced, or obsoleted by other documents at any
time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."

The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt.

The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.

This Internet-Draft will expire on November 23, 2007. January 10, 2008.

Abstract

ssmping is a tool that is used to check whether one can receive SSM,
as well as obtaining some additional information. ssmping requires
both a client and a server supporting the ssmping protocol to work.
We here specify this protocol.

Requirements Language

The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [1].

Table of Contents

1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Protocol description . Architecture . . . . . . . . . . . . . . . . . . . . 3
3. Options . . . . . . . 3
3. Protocol specification . . . . . . . . . . . . . . . . . . . . 4
3.1. Option format . . . . . . . . . . . . . . . . . . . . . . 4 5
3.2. Defined Options . . . . . . . . . . . . . . . . . . . . . 5
4. Packet Format . . . . . . . . . . . . . . . . . . . . . . . . 7
5. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 8
6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8
7. Security Considerations . . . . . . . . . . . . . . . . . . . 8
8. References . . . . . . . . . . . . . . . . . . . . . . . . . . 9
8.1. Normative References . . . . . . . . . . . . . . . . . . . 9
8.2. Informative References . . . . . . . . . . . . . . . . . . 9
Author's Address .
Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . . 9
Intellectual Property and Copyright Statements . . . . . . . . . . 10

1. Introduction

ssmping is a tool that is used designed to allow a local host to check
whether one can it is able to receive SSM,
and a multicast flow (SSM by default, or
ASM when specific options are used) originated by a remote host.
Additionally it can also give is able to report other information like such as the
amount of time used to establish the multicast tree, the number of router
hops the flow's packets have traveled, traveled as well as the packet delay and
loss. The ssmping This functionality resembles in part the ICMP echo request/
reply using Echo Request/
Reply infrastructure but over UDP and a client and a server that supports implemented by both the ssmping
protocol. It is used by a
client to verify that it can receive
multicast from the server, as well as some additional information. and server. The protocol as specified here specified is based on an the
actual implementation of a the ssmping tool [3] that has been found useful which is widely used by many organisations.
the Internet community to conduct multicast connectivity tests.

2. Protocol description Architecture

Before going into the protocol details we will describe how it is
used and what information it may provide. The typical usage of an
ssmping session is as follows. A server runs continuously in order
to serve request from clients. At some point When a client application may try host decides to verify the
multicast reception from such a server. The client will need to know a unicast address specific server (knowing one of a server. The the
server's unicast addresses is required), the ssmping client joins an
SSM channel (S,G) where S is a unicast address of the server, target server
and G is a standardised the standard multicast group defined for use by ssmping.

After joining the channel, the client sends ssmping requests as
encapsulated in UDP to a the standardised ssmping port and the unicast
address of the server. The requests are sent periodically, e.g. once
per second, to the server. The requests contain a serial number, and
typically a timestamp. The requests are typically, but not
necessarily always, simply echoed back by the server. To each
request, the server sends two replies. One as unicast back to the
port and address the request was sourced from, and also as multicast
back to the port the request came from. It is currently left open
which port the request is sourced from, whether this port should be
standardised or not. The TTL or Hop Limit of the replies are set to
64. The client should leave the SSM channel when it has finished its
measurements.

By use of this protocol, a client can obtain information on several
aspects of the multicast quality. First of all, by receiving unicast
replies, it can verify that the server is receiving the unicast
requests, is operational and responding. Hence provided that the
client receives unicast replies, a failure in receiving multicast is
indeed caused by
indicates either a multicast problem. problem or a multicast administrative
restriction. If it does receive multicast, it knows not only that it
can receive, but receive; it may get some
information on how long estimate the amount of time it takes took to establish
the multicast tree (at least if it is in the range of seconds),
whether there are packet drops, and the length and variation of round
trip times (RTT). For unicast the RTT is the time from the unicast
request is sent to when the reply is received. For The measured
multicast we RTT also talk about RTT, but then we
mean from references the client's unicast request is sent to when the multicast reply is
received. request. Since
the server sets TTL or Hop Limit to 64, it can also know the number
of router hops it is away from the source. By
comparing with obtaining the same
values by the unicast replies, it can see whether there are the host may compare its multicast and
unicast results and is able to check for differences in RTT and the number of hops etc for unicast and multicast.
hops, RTT, etc. Provided that the server sends the unicast and
multicast replies nearly simultaneously, it may also be able to
measure difference in one way delay for unicast and multicast on the
path from server to client, and also if there are differences in delay variation.
Servers may optionally specify a timestamp. This may be useful if since
the unicast and multicast replies can not be sent nearly
simultaneously, simultaneously (the
delay depending on the host's operating system and load), or if when the
client and server have synchronised clocks.

3. Protocol specification

The ssmping requests and replies have a common format, one octet
specifying the message type, followed by a number of options in TLV
(Type, Length and Value) format. This makes the protocol easily
extendible. Generally the client includes a number of options in the
request, and a server may simply echo the content back (only changing
the message type), without inspecting the options. However, there
are a number of options that a server implementation may support,
where the client may ask for a certain information or behaviour from
the server. In some cases the server will need to add options in the
response. The response will then first contain the exact options
from the request, and then right after those, options appended by the
server.

3. Options

There are

This document defines a number of different options. Most of the Some options are
only used
don't require processing by clients servers and are simply echoed back by the server, where returned
unmodified in the
server doesn't care about their contents. reply. There are however some other client options that
the server may care about. There are about, and also server options that may be
requested by the a client. Generally a simple client will only include a
few options, and get exactly the same options and values echoed back.
Strictly speaking the protocol could work without any options. Without sending any options a client would
still be able to tell whether multicast is working or not, however
with The
protocol here defined does not require the use of any options, and a
client may operate without specifying any. However some of the basic
options a allow the client can to obtain a lot
more additional information.

Unless otherwise specified, an option MUST NOT be used multiple times
in a request. Also unless otherwise specified, an option MUST NOT be
appended by the server multiple times. Note that some options, like
timestamp, may be added by both the client and the server. In that
case the timestamp option would be in the response twice. But as
said above, it is not used multiple times in the request, and not
appended multiple times by the server.

3.1. Option format

All options are TLVs formatted as specified below.

0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value |
| . |
| . |
| . |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

Type (2 octets) specifies the option. The different options are
defined below.

Length (2 octets) specifies the length of the value. value field. Depending
on the option type it can be from 0 to 65535.

Value. The value must always be of the specified length. See the
respective option definitions for possible values. If the length is
0, the value field is not included.

3.2. Defined Options

Client Identifier, type 1. Length MUST be non-zero. Only used by
clients. A client SHOULD include this. The client may use any value
it likes to be able to detect whether a reply is a reply to this
query or not. A server should treat this as opaque data, and simply
leave it unchanged in the reply. The value might be a process ID,
perhaps process ID combined with an IP address because it may receive
multicasted responses to queries from other clients. It is left to
the client implementor how to make use of this.

Sequence number, type 2. Length MUST be 4. Only used by clients. A
client SHOULD include this. This contains a 32 bit sequence number.
The values would typically start at 1 and increase by one for each
request in a sequence.

Timestamp, type 3. Length MUST be 8 bytes. A client SHOULD include
this. A server MAY support this. If supported it SHOULD be included
in the reply if requested by the client. The timestamp specifies the
time when the message (query or reply) is sent. The first 4 bytes
specify the number of seconds since the Epoch (beginning of the year
1970). The next 4 bytes specify the number of microseconds since the
last second since the Epoch.

Multicast group, type 4. Length MUST be greater than 1. It is
optional for clients and servers to support this. It allows a client
to specify which group the server should send to. This is currently
used by a tool called "asmping" to test ASM connectivity. The server
may have restrictions on which groups can be used. The format of the
option value is as below.

0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Addr Family | Multicast group address... |
+-+-+-+-+-+-+-+-+ .... |

The address family is a value 0-127 as assigned by IANA for Internet
Address Families [2]. This is followed by the group address. For
IPv4 the option value length will be 5, for IPv6 17.

Option Request Option, type 5. Length MUST be greater than 1. The
option contains a list of option types of options that the client
requests from the server. Supporting this is optional for both
clients and servers. The length of this option will be a non-zero
even number, since it contains option types that each are two octets.
The format of the value is as below.

0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option Type | Option Type |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ..... |

The value might contain an odd number of options, including just one.
This option might be used by the client to ask the server to include
options like timestamp or version.

Version, type 6. Length MUST be non-zero. Supporting this option is
optional. A server supporting this option SHOULD add it if and only
if requested by the client. The value is just unformatted text that
might contain vendor and version information for the server
implementation. It may also contain information on which options the
server supports.

Reply size, type 7. Length MUST be 2 octets.

Type 7, Reserved. This option is
optional for clients and servers. It can be used to request the
server response to be of a certain size. The code value specifies the
desired response size in octets. A server supporting this will if
necessary use the pad option to increase the size of the response. A
server should however not try to make the response shorter due to
this option. That is, it should not omit or shorten any was used by early
implementations for an option
values to try to accommodate this. The response that now is deprecated. This should never no
longer be
shorter than if this option were not included. Also, the pad option
requires at least 3 octets, so the server will not pad the response
size if the requested size is used. Clients MUST not at least 3 octets longer than the
normal response size. use this option, and Servers MUST
ignore it.

Pad, type 8. Length can be anything, including 0. This option is
used by servers clients to increase the response size if the client asks for request sizes in order to get
responses of a reply that is larger than what particular size. If the server normally would send. The
addition of this option consumes a minimum of 3 octets, so adds any options when
responding, it should
only be added if possible make the requested size is at least 3 octets more than response the same size of as
the normal (non-padded) response. request by shrinking the pad option (i.e., not simply including
it like for other client options). If the options added by the
server consume as much space as the pad option does, or more, the
server should remove the entire pad option.

4. Packet Format

The format of the ssmping messages is a one octet message type,
followed by a variable number of options.

0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Option |
+-+-+-+-+-+-+-+-+ . |
| . |
| . |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option |
| . |
| . |
| . |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
.
.
.
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Option |
| . |
| . |
| . |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

There are two message types defined. Type 81 (the character Q in
ASCII) specifies a query. Type 65 (the character A in ASCII)
specifies a response (answer).

The options follow right after the type octet and are not aligned in
any way (no spacing or padding). I.e., options might start at any
octet boundary. The option format is specified below above.

5. Acknowledgements

The ssmping idea concept was proposed by Pavan Namburi, Kamil Sarac and
Kevin C. Almeroth in the paper SSM-Ping: A Ping Utility for Source
Specific Multicast, and also the Internet Draft
draft-sarac-mping-00.txt. Mickael Hoerdt has contributed with
several ideas. Alexander Gall, Nicholas Humfrey, Nick Lamb and Dave
Thaler have contributed in different ways to my implementation of the
ssmping tools [3]. Hugo Santos has made an
independent implementation of an ssmping server. Many people in communities like TERENA, Internet2
and the M6Bone have used early implementations of ssmping and
provided feedback that have influenced the current protocol. Thanks
to Kevin Almeroth, Toerless Eckert, Gorry Fairhurst, Liu Hui, Olav
Kvittem, Kamil Sarac and Sarac, Pekka Savola, Trond Skjesol and Cao Wei for
reviewing and providing feedback on this draft.

6. IANA Considerations

As currently specified, ssmping would need a well known port number
which the servers listen to. It might be desirable to use SRV
records instead or in addition to this. For IPv6 SSM ssmping should
ideally have a reserved group ID. For the optional ASM functionality
it would be useful to have a reserved IPv6 group ID, this may be the
same as the one used for SSM. It may also be useful to have a
dedicated group for the optional IPv4 ASM functionality. This
section needs further work.

There may also be a need for an ssmping option registry. The exact
IANA considerations need to be clarified before this document can go
to working group last call.

7. Security Considerations

There are some security issues to consider. One is that a host may
send a request with an IP source address of another host, and make a
random ssmping server on the Internet send packets to this other
host. This is fairly harmless. The worst case is if the host
receiving the unicast replies also happen to be performing an ssmping
test towards that particular server. In this unlikely event there
would be an amplification effect where the host receives twice as
many replies as there are requests sent. An ssmping server should
perform rate limiting, to guard against this being used as an a DoS
attack. A client should also use the client identifier option to be
able to distinguish replies to its own requests from replies that
might be to other requests. How the protocol should be designed to
cope with rate limiting at the server requires further study. One
possibility might be that the server can choose to send generic
replies, e.g. a packet every second without the usual client options
but including sequence number and server time stamp, and where
clients do not send requests as long as they receive generic replies.

8. References

8.1. Normative References

[1] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.

[2] "IANA, Address Family Numbers",
<http://www.iana.org/assignments/address-family-numbers>.

8.2. Informative References

[3] "ssmping implementation",
<http://www.venaas.no/multicast/ssmping/>.

Author's Address

Authors' Addresses

Stig Venaas
UNINETT
Trondheim NO-7465
Norway

Email: venaas@uninett.no

Hugo Santos
Urb Glicinias, Smart Residence, 211
Aveiro 3810
Portugal

Email: hugo@fivebits.net

Full Copyright Statement

This document is subject to the rights, licenses and restrictions
contained in BCP 78, and except as set forth therein, the authors
retain all their rights.

This document and the information contained herein are provided on an
"AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS
OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND
THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF
THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

Intellectual Property

The IETF takes no position regarding the validity or scope of any
Intellectual Property Rights or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; nor does it represent that it has
made any independent effort to identify any such rights. Information
on the procedures with respect to rights in RFC documents can be
found in BCP 78 and BCP 79.

Copies of IPR disclosures made to the IETF Secretariat and any
assurances of licenses to be made available, or the result of an
attempt made to obtain a general license or permission for the use of
such proprietary rights by implementers or users of this
specification can be obtained from the IETF on-line IPR repository at
http://www.ietf.org/ipr.

The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights that may cover technology that may be required to implement
this standard. Please address the information to the IETF at
ietf-ipr@ietf.org.

Acknowledgment

Funding for the RFC Editor function is provided by the IETF
Administrative Support Activity (IASA).