--- 1/draft-ietf-bfd-unaffiliated-echo-01.txt 2021-06-22 20:13:09.438640927 -0700 +++ 2/draft-ietf-bfd-unaffiliated-echo-02.txt 2021-06-22 20:13:09.458641432 -0700 @@ -1,24 +1,24 @@ BFD Working Group W. Cheng Internet-Draft R. Wang Updates: 5880 (if approved) China Mobile Intended status: Standards Track X. Min -Expires: May 6, 2021 ZTE Corp. +Expires: December 24, 2021 ZTE Corp. R. Rahman - Cisco Systems + Individual R. Boddireddy Juniper Networks - November 2, 2020 + June 22, 2021 Unaffiliated BFD Echo Function - draft-ietf-bfd-unaffiliated-echo-01 + draft-ietf-bfd-unaffiliated-echo-02 Abstract Bidirectional Forwarding Detection (BFD) is a fault detection protocol that can quickly determine a communication failure between two forwarding engines. This document proposes a use of the BFD Echo function where the local system supports BFD but the neighboring system does not support BFD. Status of This Memo @@ -29,364 +29,393 @@ Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet- Drafts is at https://datatracker.ietf.org/drafts/current/. Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress." - This Internet-Draft will expire on May 6, 2021. + This Internet-Draft will expire on December 24, 2021. Copyright Notice - Copyright (c) 2020 IETF Trust and the persons identified as the + Copyright (c) 2021 IETF Trust and the persons identified as the document authors. All rights reserved. This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Simplified BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Simplified BSD License. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . 2 + 1.1. Conventions Used in This Document . . . . . . . . . . . . 3 2. Updates to RFC 5880 . . . . . . . . . . . . . . . . . . . . . 3 3. Unaffiliated BFD Echo Procedures . . . . . . . . . . . . . . 6 - 4. Unaffilicated BFD Echo Applicability . . . . . . . . . . . . 7 + 4. Unaffiliated BFD Echo Applicability . . . . . . . . . . . . . 8 5. Security Considerations . . . . . . . . . . . . . . . . . . . 8 6. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 8 7. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . 8 - 8. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 8 - 9. References . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 9.1. Normative References . . . . . . . . . . . . . . . . . . 8 + 8. Contributors . . . . . . . . . . . . . . . . . . . . . . . . 9 + 9. References . . . . . . . . . . . . . . . . . . . . . . . . . 9 + 9.1. Normative References . . . . . . . . . . . . . . . . . . 9 9.2. Informative References . . . . . . . . . . . . . . . . . 9 - Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 9 + Authors' Addresses . . . . . . . . . . . . . . . . . . . . . . . 10 1. Introduction To minimize the impact of device/link faults on services and improve network availability, a network device must be able to quickly detect faults in communication with adjacent devices. Measures can then be taken to promptly rectify the faults to ensure service continuity. BFD [RFC5880] is a low-overhead, short-duration method to detect faults on the communication path between adjacent forwarding engines. - The faults can be on interface, data link, and even forwarding - engine. It is a single, unified mechanism to monitor any media and - protocol layers in real time. + The faults can be on interfaces, data link(s), and even the + forwarding engines. It is a single, unified mechanism to monitor any + media and protocol layers in real time. - BFD defines Asynchronous mode to satisfy various deployment - scenarios, and also supports Echo function to reduce the device + BFD defines an Asynchronous mode to satisfy various deployment + scenarios. It also supports an Echo function to reduce the device requirement for BFD. When the Echo function is activated, the local system sends BFD Echo packets and the remote system loops back the received Echo packets through the forwarding path. If several consecutive BFD Echo packets are not received by the local system, then the BFD session is declared to be Down. When using BFD Echo function, there are two typical scenarios as below: - o Full BFD protocol capability with affiliated Echo function: this + o Full BFD protocol capability with affiliated Echo function: This scenario requires both the local device and the neighboring device - to support full BFD protocol. + to support the full BFD protocol. - o Only BFD Echo function without full BFD protocol capability: - this scenario requires only the local device to support sending - and demultiplexing BFD Control packets. + o BFD Echo-Only function without full BFD protocol capability: This + scenario requires only the local device to support sending and + demultiplexing BFD Control packets. - The two typical scenarios are both reasonable and useful, and the - latter is referred to as Unaffiliated BFD Echo function in this - document. + The latter scenario is referred to as Unaffiliated BFD Echo function + in this document. Section 6.2.2 of [BBF-TR-146] describes one use case of the Unaffiliated BFD Echo function, and at least one more use case is - known in the field BFD deployment. + known to be deployed. This document describes the use of the Unaffiliated BFD Echo function over IPv4 and IPv6 for single IP hop. +1.1. Conventions Used in This Document + + The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", + "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and + "OPTIONAL" in this document are to be interpreted as described in BCP + 14 [RFC2119] [RFC8174] when, and only when, they appear in all + capitals, as shown here. + 2. Updates to RFC 5880 The Unaffiliated BFD Echo function described in this document reuses the BFD Echo function as described in [RFC5880] and [RFC5881], but - does not require BFD asynchronous mode. When using the Unaffiliated + does not require BFD Asynchronous mode. When using the Unaffiliated BFD Echo function, only the local system has the BFD protocol - enabled, the remote system just loops back the received BFD Echo + enabled; the remote system just loops back the received BFD Echo packets as regular data packets. - With that said, this document updates [RFC5880] with respect to its - descriptions on the BFD Echo function as follows. + This document updates [RFC5880] with respect to its descriptions on + the BFD Echo function as follows. - o [RFC5880] states in the 4th paragraph of Section 3.2: + o The 4th paragraph of Section 3.2 of [RFC5880] is updated as below: + + OLD TEXT + + An adjunct to both modes is the Echo function. + + NEW TEXT + + An adjunct or complement to both modes is the Echo function. + + OLD TEXT - An adjunct to both modes is the Echo function. When the Echo - function is active, a stream of BFD Echo packets is transmitted in - such a way as to have the other system loop them back through its - forwarding path. If a number of packets of the echoed data stream - are not received, the session is declared to be down. The Echo - function may be used with either Asynchronous or Demand mode. Since the Echo function is handling the task of detection, the rate of periodic transmission of Control packets may be reduced (in the case of Asynchronous mode) or eliminated completely (in the case of Demand mode). - * This paragraph is now updated to: + NEW TEXT - An adjunct or complement to both modes is the Echo function. When - the Echo function is active, a stream of BFD Echo packets is - transmitted in such a way as to have the other system loop them - back through its forwarding path. If a number of packets of the - echoed data stream are not received, the session is declared to be - down. The Echo function may be used with either Asynchronous or - Demand mode. Since the Echo function is handling the task of - detection, the rate of periodic transmission of Control packets - may be reduced (in the case of Asynchronous mode) or eliminated - completely (in the case of Demand mode). The Echo function may - also be used independently, with neither Asynchronous nor Demand - mode. + Since the Echo function is handling the task of detection, the + rate of periodic transmission of Control packets may be reduced + (in the case of Asynchronous mode) or eliminated completely (in + the case of Demand mode). The Echo function may also be used + independently, with neither Asynchronous nor Demand mode. - o [RFC5880] states in the 3rd and 9th paragraphs of Section 6.1: + o The 3rd and 9th paragraphs of Section 6.1 of [RFC5880] are updated + as below: + + OLD TEXT Once the BFD session is Up, a system can choose to start the Echo function if it desires and the other system signals that it will - allow it. The rate of transmission of Control packets is - typically kept low when the Echo function is active. + allow it. + + NEW TEXT + + When a system is running with Asynchronous mode, once the BFD + session is Up, it can choose to start the Echo function if it + desires and the other system signals that it will allow it. + + OLD TEXT If the session goes Down, the transmission of Echo packets (if any) ceases, and the transmission of Control packets goes back to the slow rate. - * The two paragraphs are now updated to: - - When a system is running with Asynchronous mode, once the BFD - session is Up, it can choose to start the Echo function if it - desires and the other system signals that it will allow it. The - rate of transmission of Control packets is typically kept low when - the Echo function is active. + NEW TEXT In Asynchronous mode, if the session goes Down, the transmission of Echo packets (if any) ceases, and the transmission of Control packets goes back to the slow rate. - o [RFC5880] states in the 2nd paragraph of Section 6.4: + o The 2nd paragraph of Section 6.4 of [RFC5880] is updated as below: + OLD TEXT When a system is using the Echo function, it is advantageous to choose a sedate reception rate for Control packets, since liveness - detection is being handled by the Echo packets. This can be - controlled by manipulating the Required Min RX Interval field (see - section 6.8.3). + detection is being handled by the Echo packets. - * This paragraph is now updated to: + NEW TEXT When a system is using the Echo function with Asynchronous mode, it is advantageous to choose a sedate reception rate for Control packets, since liveness detection is being handled by the Echo - packets. This can be controlled by manipulating the Required Min - RX Interval field (see section 6.8.3). + packets. - o [RFC5880] states in the 2nd paragraph of Section 6.8: + o The 2nd paragraph of Section 6.8 of [RFC5880] is updated as below: + + OLD TEXT When a system is said to have "the Echo function active" it means that the system is sending BFD Echo packets, implying that the session is Up and the other system has signaled its willingness to loop back Echo packets. - * This paragraph is now updated to: + NEW TEXT When a system in Asynchronous or Demand mode is said to have "the Echo function active" it means that the system is sending BFD Echo packets, implying that the session is Up and the other system has signaled its willingness to loop back Echo packets. - o [RFC5880] states in the 7th paragraph of Section 6.8.3: + o The 7th paragraph of Section 6.8.3 of [RFC5880] is updated as + below: + + OLD TEXT When the Echo function is active, a system SHOULD set bfd.RequiredMinRxInterval to a value of not less than one second - (1,000,000 microseconds). This is intended to keep received BFD - Control traffic at a negligible level, since the actual detection - function is being performed using BFD Echo packets. + (1,000,000 microseconds). - * This paragraph is now updated to: + NEW TEXT When the Echo function is active with Asynchronous mode, a system SHOULD set bfd.RequiredMinRxInterval to a value of not less than - one second (1,000,000 microseconds). This is intended to keep - received BFD Control traffic at a negligible level, since the - actual detection function is being performed using BFD Echo - packets. + one second (1,000,000 microseconds). - o [RFC5880] states in the 1st and 2nd paragraphs of Section 6.8.9: + o The 1st and 2nd paragraphs of Section 6.8.9 of [RFC5880] are + updated as below: + OLD TEXT BFD Echo packets MUST NOT be transmitted when bfd.SessionState is not Up. BFD Echo packets MUST NOT be transmitted unless the last BFD Control packet received from the remote system contains a nonzero value in Required Min Echo RX Interval. - BFD Echo packets MAY be transmitted when bfd.SessionState is Up. - The interval between transmitted BFD Echo packets MUST NOT be less - than the value advertised by the remote system in Required Min - Echo RX Interval, except as follows: - - A 25% jitter MAY be applied to the rate of transmission, such - that the actual interval MAY be between 75% and 100% of the - advertised value. A single BFD Echo packet MAY be transmitted - between normally scheduled Echo transmission intervals. - - * The two paragraphs are now updated to: + NEW TEXT When a system is using the Echo function with either Asynchronous or Demand mode, BFD Echo packets MUST NOT be transmitted when bfd.SessionState is not Up, and BFD Echo packets MUST NOT be transmitted unless the last BFD Control packet received from the remote system contains a nonzero value in Required Min Echo RX Interval. + OLD TEXT + + BFD Echo packets MAY be transmitted when bfd.SessionState is Up. + The interval between transmitted BFD Echo packets MUST NOT be less + than the value advertised by the remote system in Required Min + Echo RX Interval... + + NEW TEXT + When a system is using the Echo function with either Asynchronous or Demand mode, BFD Echo packets MAY be transmitted when bfd.SessionState is Up, and the interval between transmitted BFD Echo packets MUST NOT be less than the value advertised by the - remote system in Required Min Echo RX Interval, except as follows: - - A 25% jitter MAY be applied to the rate of transmission, such - that the actual interval MAY be between 75% and 100% of the - advertised value. A single BFD Echo packet MAY be transmitted - between normally scheduled Echo transmission intervals. + remote system in Required Min Echo RX Interval... 3. Unaffiliated BFD Echo Procedures As shown in Figure 1, device A supports BFD, whereas device B does - not support BFD. To rapidly detect any IP forwarding faults between - device A and device B, a BFD Echo session MUST be created at device - A, and the BFD Echo session is RECOMMENDED to follow the BFD state - machine defined in Section 6.2 of [RFC5880], except that the received - state is not sent but echoed from the remote system. In this case, - although BFD Echo packets are transmitted with destination UDP port - 3785 as defined in [RFC5881], the BFD Echo packets sent by device A - are BFD Control packets too, the looped BFD Echo packets back from - device B would drive BFD state change at device A, substituting the - BFD Control packets sent from the BFD peer. + not support BFD. Device A would send BFD Echo packets, and after + receiving the BFD Echo packets sent from device A, the one-hop-away + BFD peer device B immediately loops them back by normal IP + forwarding, this allows device A to rapidly detect a connectivity + loss to device B. Note that device B would not intercept any + received BFD Echo packet or parse any BFD protocol field within the + BFD Echo packet. + + To rapidly detect any IP forwarding faults between device A and + device B, a BFD Echo session MUST be created at device A, and the BFD + Echo session is RECOMMENDED to follow the BFD state machine defined + in Section 6.2 of [RFC5880], except that the received state is not + sent but echoed from the remote system, and AdminDown state is ruled + out because AdminDown effectively means removal of BFD Echo session. + In this case, although BFD Echo packets are transmitted with + destination UDP port 3785 as defined in [RFC5881], the BFD Echo + packets sent by device A are BFD Control packets too, the looped BFD + Echo packets back from device B would drive BFD state change at + device A, substituting the BFD Control packets sent from the BFD + peer. Also note that when device A receives looped BFD Control + packets, the validation procedures of [RFC5880] are used. Once a BFD Echo session is created at device A, it starts sending BFD Echo packets, which SHOULD include a BFD Echo session demultiplexing - field, such as BFD Your Discriminator defined in [RFC5880] (BFD My - Discriminator can be set to 0 to avoid confusion), except that device - A can use IP source address or UDP source port to demultiplex BFD - Echo session, or there is only one BFD Echo session running at device - A. Device A would send BFD Echo packets with IP destination address - destined for itself, such as the IP address of interface 1 of device - A. All BFD Echo packets for the session MUST be sent with a Time to - Live (TTL) or Hop Limit value of 255. + field, such as BFD "Your Discriminator" defined in [RFC5880] (BFD "My + Discriminator" can be set to 0 to avoid confusion), except that + device A can use IP source address or UDP source port to demultiplex + BFD Echo session, or there is only one BFD Echo session running at + device A. Device A would send BFD Echo packets with IP destination + address destined for itself, such as the IP address of interface 1 of + device A. All BFD Echo packets for the session MUST be sent with a + Time to Live (TTL) or Hop Limit value of 255. - Considering the BFD peer wouldn't advertise Required Min Echo RX - Interval as defined in [RFC5880], the transmit interval for sending - BFD Echo packets MUST be provisioned at device A, how to make sure - the BFD peer is willing and able to loop back BFD Echo packets sent - with the provisioned transmit interval is outside the scope of this - document. Considering the BFD peer wouldn't advertise Detect Mult as - defined in [RFC5880], the Detect Mult for calculating the Detection - Time MUST be provisioned at device A, the Detection Time in device A - is equal to the provisioned Detect Mult multiplied by the provisioned - transmit interval. + "Desired Min TX Interval" and "Required Min RX Interval" defined in + [RFC5880] may be populated with one second within the BFD Echo + packet, which however has no real application and would be ignored by + the receiver. - After receiving the BFD Echo packets sent from device A, the one-hop- - away BFD peer device B immediately loops them back by normal IP - forwarding, this allows device A to rapidly detect a connectivity - loss to device B. + Considering the BFD peer wouldn't advertise "Required Min Echo RX + Interval" as defined in [RFC5880], the transmission interval for + sending BFD Echo packets MUST be provisioned at device A, how to make + sure the BFD peer is willing and able to loop back BFD Echo packets + sent with the provisioned transmission interval is outside the scope + of this document. Similar to what's specified in [RFC5880], the BFD + Echo session begins with the periodic, slow transmission of BFD Echo + packets, the slow transmission rate SHOULD be no less then one second + per packet, until the session is Up, after that the provisioned + transmission interval is applied, and reverting back to the slow rate + once the session goes Down. Considering the BFD peer wouldn't + advertise "Detect Mult" as defined in [RFC5880], the "Detect Mult" + for calculating the Detection Time MUST be provisioned at device A, + the Detection Time in device A is equal to the provisioned "Detect + Mult" multiplied by the provisioned transmission interval. Device A Device B - BFD Echo session + BFD Enabled BFD Echo packets loopback - +--------+ +---------+ - | A |---------------------------------| B | + +--------+ BFD Echo session +---------+ + | A |--------------------------------| B | | |Inf 1 Inf 1| | +--------+10.1.1.1/24 10.1.1.2/24+---------+ BFD is supported. BFD is not supported. - Figure 1: Unaffiliated BFD Echo deployment scenario - -4. Unaffilicated BFD Echo Applicability + Figure 1: Unaffiliated BFD Echo diagram - With the more and more application of BFD detection, there are some - scenarios the BFD Echo function is deployed. And due to the - different capabilities of the devices deploying BFD Echo function, - it's required to apply Unaffiliated BFD Echo to the devices that - couldn't afford the overhead of the full BFD protocol capability, - such as the servers running virtual machines or some Internet of - Things (IoT) devices. Unaffiliated BFD Echo can be used when two - devices are connected and only one of them supports BFD protocol - capability. +4. Unaffiliated BFD Echo Applicability - Unaffiliated BFD Echo function is reasonable and useful. Firstly, - Unaffiliated BFD Echo can use BFD protocol capability at the local - BFD-supported device, while using IP forwarding capability at the - peer BFD-unsupported device, so Unaffiliated BFD Echo can support - fast detecting and manage BFD sessions very effectively. Secondly, - it is scalable when using Unaffiliated BFD Echo to adapt to different - capabilities of devices. + Some devices that would benefit from the use of BFD may be unable to + support the full BFD protocol. Examples of such devices include + servers running virtual machines, or Internet of Things (IoT) + devices. The Unaffiliated BFD Echo function can be used when two + devices are connected and only one of them supports the BFD protocol, + and the other is capable of looping BFD Echo packets. 5. Security Considerations - Unicast Reverse Path Forwarding (uRPF), as specified in [RFC3704] and - [RFC8704], is a security feature that prevents the IP address - spoofing attacks which is commonly used in DoS, DDoS. uRPF has two - modes called strict mode and loose mode. uRPF strict mode means that - the router will perform checks for all incoming packets on a certain - interface: whether the router has a matching entry for the source IP - in the routing table and whether the router uses the same interface - to reach this source IP as where the router received this packet on. - Note that the use of BFD Echo function would prevent the use of uRPF - in strict mode. + All Security Considerations from [RFC5880] and [RFC5881] apply. + + Note that the Unaffiliated BFD Echo function prevents the use of + Unicast Reverse Path Forwarding (URPF) [RFC3704] [RFC8704] in strict + mode. + + As specified in Section 5 of [RFC5880], since BFD Echo packets may be + spoofed, some form of authentication SHOULD be included. Considering + the BFD Echo packets in this document are also BFD Control packets, + the "Authentication Section" as defined in [RFC5880] for BFD Control + packet is RECOMMENDED to be included within the BFD Echo packet. + + In order to mitigate the potential reflector attack by the remote + attackers, or infinite loop of the BFD Echo packets, it's RECOMMENDED + to put two requirements on the device looping BFD Echo packets, the + first one is that a packet SHOULD NOT be looped unless it has a TTL + or Hop Limit value of 255, and the second one is that a packet being + looped MUST NOT reset the TTL or Hop Limit value to 255, and MUST use + a TTL or Hop Limit value of 254. 6. IANA Considerations This document has no IANA action requested. 7. Acknowledgements The authors would like to acknowledge Ketan Talaulikar, Greg Mirsky and Santosh Pallagatti for their careful review and very helpful comments. + The authors would like to acknowledge Jeff Haas for his insightful + review and very helpful comments. + 8. Contributors Liu Aihua ZTE Email: liu.aihua@zte.com.cn Qian Xin ZTE Email: qian.xin2@zte.com.cn Zhao Yanhua ZTE Email: zhao.yanhua3@zte.com.cn 9. References 9.1. Normative References + [RFC2119] Bradner, S., "Key words for use in RFCs to Indicate + Requirement Levels", BCP 14, RFC 2119, + DOI 10.17487/RFC2119, March 1997, + . + [RFC5880] Katz, D. and D. Ward, "Bidirectional Forwarding Detection (BFD)", RFC 5880, DOI 10.17487/RFC5880, June 2010, . [RFC5881] Katz, D. and D. Ward, "Bidirectional Forwarding Detection (BFD) for IPv4 and IPv6 (Single Hop)", RFC 5881, DOI 10.17487/RFC5881, June 2010, . + [RFC8174] Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC + 2119 Key Words", BCP 14, RFC 8174, DOI 10.17487/RFC8174, + May 2017, . + 9.2. Informative References [BBF-TR-146] Broadband Forum, "BBF Technical Report - Subscriber Sessions Issue 1", 2013, . [RFC3704] Baker, F. and P. Savola, "Ingress Filtering for Multihomed Networks", BCP 84, RFC 3704, DOI 10.17487/RFC3704, March 2004, . @@ -394,38 +423,39 @@ [RFC8704] Sriram, K., Montgomery, D., and J. Haas, "Enhanced Feasible-Path Unicast Reverse Path Forwarding", BCP 84, RFC 8704, DOI 10.17487/RFC8704, February 2020, . Authors' Addresses Weiqiang Cheng China Mobile Beijing - CN + China Email: chengweiqiang@chinamobile.com Ruixue Wang China Mobile Beijing - CN + China Email: wangruixue@chinamobile.com Xiao Min ZTE Corp. Nanjing - CN + China Email: xiao.min2@zte.com.cn + Reshad Rahman - Cisco Systems + Individual Kanata - CA + Canada - Email: rrahman@cisco.com + Email: reshad@yahoo.com Raj Chetan Boddireddy Juniper Networks Email: rchetan@juniper.net